Spraying Machine
The glue used has excellent bonding properties and can form a strong and lasting bond on different material surfaces. When the glue contacts the material surface, it can quickly adsorb to the material surface in a short time to form a preliminary bond. The glue is specially formulated and has good water resistance. Even in the case of long-term immersion or frequent contact with water, the glue can still maintain its bonding strength and stability without hydrolysis, softening or loss of bonding.
Using advanced spraying technology, through the precise control of nozzle design, spraying pressure, flow rate and other parameters, ensure that the glue can be evenly distributed on the surface of the bonded material. Different materials and products have different requirements for the amount of glue. The amount of glue can be flexibly adjusted according to the material characteristics, the requirements of the bonding part and the regulations of the production process. This precise glue control capability enables the hot melt adhesive machine to adapt to various complex bonding tasks and improve the product yield and production efficiency.
The design concept of using water as a solvent reflects the high attention paid by modern industry to environmental protection. In the aqueous system, water is used as a dispersion medium and does not contain organic solvents or the organic solvent content is extremely low, thus effectively avoiding pollution to the atmospheric environment. During use, no harmful gases such as volatile organic compounds (VOCS) will be emitted, which will not cause any harm to the health of operators, ensuring the cleanliness and safety of the production environment.
High-quality glue barrel treatment: The glue barrel is treated with Teflon, which is corrosion-resistant and non-sticky. It can withstand high temperatures, is easy to clean up residual hot melt glue, and can make solid hot melt glue melt quickly and evenly, and is not easy to carbonize.
Applicable to various types of adhesives: Applicable to hot melt adhesives of various types (granular, block, powder, etc.) and shapes (round, square, irregular, etc.) to meet the diverse needs of users.
Glue circuit isolation design: The unique glue feeding structure makes the glue circuit absolutely isolated from the air, avoiding oxidation of hot melt adhesive, ensuring its performance and quality stability, extending service life and reducing material waste.
Anti-clogging filter design: Two-stage filter equipment is used, first coarse filtration and then fine filtration, to remove impurities in the hot melt adhesive, reduce nozzle clogging, and ensure the normal operation of the nozzle and the continuity and stability of coating.
The glue barrel adopts a safe pressure maintenance device, which can ensure the stability of the pressure in the glue barrel and avoid problems such as uneven hot melt adhesive spraying and unstable glue quantity caused by pressure fluctuations. At the same time, the glue barrel is also equipped with a unique ultra-high temperature control device, which can accurately control the temperature in the glue barrel, so that the hot melt adhesive is always kept in the best viscosity state, thereby ensuring the consistency and stability of the gluing effect.
The equipment adopts a unique setting in the air system. This design can effectively ensure that the air will not get water or carbonize during the operation of the equipment. It is very important to ensure the stable operation of the equipment and extend the service life of the equipment. As one of the power sources for the operation of the equipment, if the air gets water or carbonizes, it may cause the performance of the equipment to decline, frequent failures, and even damage the key components of the equipment.
The glue barrel adopts a safe pressure maintenance device, which can ensure the stability of the pressure in the glue barrel and avoid problems such as uneven hot melt adhesive spraying and unstable glue quantity caused by pressure fluctuations. At the same time, the glue barrel is also equipped with a unique ultra-high temperature control device, which can accurately control the temperature in the glue barrel, so that the hot melt adhesive is always kept in the best viscosity state, thereby ensuring the consistency and stability of the gluing effect.
The equipment adopts a unique setting in the air system. This design can effectively ensure that the air will not get water or carbonize during the operation of the equipment. It is very important to ensure the stable operation of the equipment and extend the service life of the equipment. As one of the power sources for the operation of the equipment, if the air gets water or carbonizes, it may cause the performance of the equipment to decline, frequent failures, and even damage the key components of the equipment.
(1)Glue groove treatment: The glue groove is treated with Teflon, and the glue changing operation is simple.
(2)Temperature control: The temperature can be adjusted according to the characteristics of the melt adhesive to effectively prevent the hot melt adhesive from carbonizing.
(3)Control method: The motor of this machine can be controlled by a frequency converter to achieve stepless speed adjustment.
